CFE version 1.13.0-102.9 for BCM96368 (32bit,SP,BE) Build Date: 04/01/2010 (eason@bcs) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name MX29GL128EH, id 0x2221, size 16384KB ethsw: found bcm53115! CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz CPU running TP0 Total memory: 67108864 bytes (64MB) Boot Address 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 3 Board Id (0-4) : 96368MVWG Number of MAC Addresses (1-32) : 10 Base MAC Address : 40:4a:03:c6:fb:4c PSI Size (1-64) KBytes : 128 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 1 web info: Waiting for connection on socket 0. CFE> atsh ZLD Version : V1.02(BLL.1) Bootbase Version : V1.13 | 04/01/2010 Vendor Name : ZyXEL Communications Corp. Product Model : P-2812HNU-51c First MAC Address : 404A03C6FB4C Last MAC Address : 404A03C6FB55 MAC Address Quantity : 10 Default Country Code : E1 Boot Module Debug Flag : 00 RootFS Checksum : b74a6a7c Kernel Checksum : dca10607 Main Feature Bits : C0 Other Feature Bits : 5a 59 60 01 00 00 00 00-00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00-03 41 13 00 00 00 *** command status = 0 CFE> athe Available commands: ATSE show the seed of password generator ATEN set BootExtension Debug Flag ATCR Clear console screen ATSH dump manufacturer related data in ROM ATUR xmodem upload router firmware to flash ROM ATUW xmodem upload flash image to flash ROM ATBL Print boot line and board parameter info ATDU Dump memory or registers. ATBR Reset to default Romfile ATGO boot router ATSR system reboot ATMB Use for multiboot. ATHE print help For more information about a command, enter 'help command-name' *** command status = 0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Checking Reset button on GPIO 34 Wait for Multiboot Service Packet... 0 Booting from only image (0xb8020000) ... Code Address: 0x80020000, Entry Address: 0x802c5000 Decompression OK! Entry at 0x802c5000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x802c5000 Linux version 2.6.21.5 (jason@msgsw3-i7) (gcc version 4.2.3) #14 Wed Dec 22 20:32:43 CST 2010 Parallel flash device: name MX29GL128EH, id 0x2221, size 16384KB 96368MVWG prom init CPU revision is: 0002a031 Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) On node 0 totalpages: 16128 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 brcm mips: enabling icache and dcache... Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, linesize 16 bytes. Synthesized TLB refill handler (21 instructions). Synthesized TLB load handler fastpath (33 instructions). Synthesized TLB store handler fastpath (33 instructions). Synthesized TLB modify handler fastpath (32 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) Using 200.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x8108c700 SIZE=1573552, INIT=0x0 SIZE=0 Memory: 59304k/64512k available (2323k kernel code, 5192k reserved, 381k data, 100k init, 0k highmem) KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000> Calibrating delay loop... 398.33 BogoMIPS (lpj=199168) Mount-cache hash table entries: 512 NET: Registered protocol family 16 Total Flash size: 16384K with 128 sectors Address is too big. File system address: 0xb8020100 kerSysFlashInit zyxel_ivr usedBlkSize 524288 kerSysFlashInit userdefcfg usedBlkSize 131072 registering PCI controller with io_map_base unset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb BLOG v1.0 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro fuse init (API version 7.8) io scheduler noop registered (default) PPP generic driver version 2.4.2 NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver hub 1-0:1.0: over-current change on port 1 PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option drivers/usb/serial/option.c: USB Driver for GSM modems: v0.7.1 brcmboard: brcm_board_init entry kerSysScreenPciDevices: 0x14e4:0xa8d6:(slot 1) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 9) detected kerSysScreenPciDevices: 0x14e4:0x6300:(slot 10) detected SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8018 is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.1 Dec 20 2010 14:11:00 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 100k freed init started: BusyBox v1.00 (2010.12.20-06:14+0000) multi-call binary mkdir: Cannot create directory `/tmp': File exists cp: /etc/ppp/chat/*: No such file or directory BusyBox v1.00 (2010.12.20-06:14+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Broadcom Packet Flow Cache learning via BLOG enabled. Created Proc FS /procfs/fcache Constructed Broadcom Packet Flow Cache v0.1 Aug 17 2009 11:57:43 Broadcom Packet CMF (Experimental) Char Driver v0.1 Jun 30 2009 11:30:40 Registered<232> Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jun 30 2009 11:30:40 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry IPv6: add_dev failed for dsl0 Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6368B2 Ethernet Network Device v0.1 Dec 20 2010 14:10:29 KLOB extended to 2 pools KLOB extended to 3 pools KLOB extended to 4 pools KLOB extended to 5 pools Config Switch Through SPI Slave Select 0 ethsw: found bcm53115! dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered Ethernet WAN selected Broadcom Packet CMF (Experimental) SWC RESET. Broadcom Packet CMF (Experimental) SWC INITIALIZED. KLOB extended to 6 pools KLOB extended to 7 pools KLOB extended to 8 pools IPv6: add_dev failed for pktcmf_sw_sar Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jun 30 2009 11:30:40 Registered IPv6: add_dev failed for pktcmf_sar_sw Broadcom Packet CMF (Experimental) Forwarder Net Device 1 v0.1 Jun 30 2009 11:30:40 Registered Broadcom Packet CMF (Experimental) ENABLED. eth3: MAC Address: 40:4A:03:C6:FB:4C eth2: MAC Address: 40:4A:03:C6:FB:4C eth1: MAC Address: 40:4A:03:C6:FB:4C eth0: MAC Address: 40:4A:03:C6:FB:4C create_vport, eth4 ifindex = 13 eth4: MAC Address: 40:4A:03:C6:FB:4D PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: MAC addr from system pool. id:0x776c0000 wl0: MAC Address: 40:4A:03:C6:FB:4E wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.10.85.0.cpe4.402.8 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered DSP Driver: DSP init stub Endpoint: endpoint_init entry Endpoint: endpoint_init COMPLETED p8021ag: p8021ag_init entry 193 main, getpid = 196 BOS: Enter bosInit bosTimerInit Enter bosAppInit Exit bosAppInit BOS: Exit bosInit AppRegisterSignal, mm pid = 199 srtpInit....ret = 0 Enter TaskCreate rtp TaskCreate - spawn new task rtp Exit TaskCreate Enter TaskCreate rtcp TaskCreate - spawn new task rtcp Exit TaskCreate 202 ===== Release Version 4.02L.03 (build timestamp 101222_2032) ===== [ENTERED]:ICF_ES INFO: AUTO_SCALE: 1 INFO: MODE_OF_OPERATION: 0 INFO: SIP_COMPACT_HDRS: NO INFO: NW_TRACE_ENABLED: YES INFO: ICF_DEF_SIP_SERVER_PORT: 6062 INFO: ICF_DEF_SIP_PROXY_PORT: 6061 INFO: TRANSPORT_MODE: 0 INFO: ICF_SYS_RESOURCE_LIMIT: 1 [ENTERING]:icf_es_init [ICF_ES]:PORT initalized succesfully icf_port_open_ipc_channel path = /var/iptk_es.chanl the open channel succeded exit from the es init ssk:error:18.822:lck_checkBeforeEntry:175:lock required during cmsObj_getNextInSubTreeFlags Got User defined contentssk:error:19.405:oal_readConfigUserDefFlashToBuf:1409:The configuration in Rom-D is invalid ssk:error:19.405:addDefaultTwoTierLoginObject:1814:Read configuration from ROM-D failed. ssk:error:19.418:ssk_init:755:cmsMdm_init failed, ret=9852 ssk:error:19.418:main:205:initialization failed (9852), exit. smd:error:19.460:oal_processEvents:856:ssk has died. smd must exit now! smd:error:19.460:oalShm_cleanup:326:shmctl IPC_STAT failed